ALUMINUM ASSOCIATION (AA)

• AA ASD1 – Aluminum Standards and Data -

AMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA)

• AAMA 501 – Methods of Test for Exterior Walls
  AAMA 501.1 – Water Penetration (Dynamic Pressure)
  AAMA 501.2 – Diagnostic Water Leakage Field Check
  AAMA 502 – Field Testing of Windows and Sliding Glass Doors
  AAMA 507 – Thermal Performance of Fenestration
  AAMA 611 – Anodized Aluminum
  AAMA 2603 – Organic Coatings (Standard)
  AAMA 1503.1 – Thermal Transmittance & Condensation Resistance
  AAMA 2604 – Organic Coatings (High Performance)
  AAMA 2605 – Organic Coatings (Superior Performance)
  AAMA CW-10 – Care and Handling of Architectural Aluminum
  AAMA CW-11 – Design Wind Loads and Wind Tunnel Testing
  AAMA CW-DG-1 – Curtain Wall Design Guide Manual
  AAMA MCWM-1 – Metal Curtain Wall Manual
  AAMA SFM-1 – Storefront and Entrance Manual
  AAMA TIR A9 – Curtain Wall Fasteners
  AAMA TIR-A11 – Allowable Deflection of Framing Systems -

AMERICAN CONCRETE INSTITUTE (ACI)

• ACI 318/318R – Building Code Requirements for Structural Concrete -

AMERICAN INSTITUTE OF STEEL CONSTRUCTION (AISC)

• AISC 325 – Steel Construction Manual -

AMERICAN IRON AND STEEL INSTITUTE (AISI)

• Cold-Formed Steel Structural Members
  Stainless Steel Cold-Formed Structural Design -

AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)

• ANSI Z97.1 – Safety Glazing Materials
  ANSI A 250.4 – Test Procedure and Acceptance Criteria for Steel Doors & Hardware Endurance
  ANSI A 250.5 – Accelerated Physical Endurance Test Procedure for Steel Doors & Hardware Endurance
  ANSI A 156.18 – Materials and Finishes
  ANSI A 118.4 – Latex-Portland Cement Mortar -

AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE)

• ASCE 7 – Minimum Design Loads for Buildings and Structures -

AMERICAN SOCIETY FOR TESTING MATERIALS (ASTM)

• A36/A36M – Carbon Structural Steel
  A276 – Standard Specification for Stainless Steel Bars and Shape
  A463/A463M – Aluminum-Coated Steel Sheet
  A618/A618M – High-Strength Low-Alloy Tubing
  A653/A653M – Galvanized & Galvannealed Steel Sheet
  A666 – Austenitic Stainless Steel
  A780 – Standard Practice for Repair of Damage and Uncoated Areas
  of Hot-Dip Galvanize Coatings
  A792/A792M – 55% Aluminum-Zinc Alloy-Coated Steel
  A1008/A1008M – Cold-Rolled Carbon & Alloy Steel Sheet
  A1011/A1011M – Hot-Rolled Carbon & Alloy Steel Sheet
  B209/B209M – Aluminum & Aluminum-Alloy Sheet & Plate
  B221/B221M – Aluminum & Aluminum-Alloy Extruded Profiles
  B449 – Standard Test Method for Measurement of Coating Thickness by the Magnetic Method
  C509 – Elastomeric Gaskets
  C661 – Hardness of Sealants (Durometer)
  C719 – Adhesion/Cohesion of Sealants (Cyclic)
  C792 – Heat Aging of Sealants
  C794 – Adhesion-in-Peel of Sealants
  C864 – Dense Elastomeric Seals
  C920 – Elastomeric Joint Sealants
  C1036 – Flat Glass
  C1048 – Heat-Treated Glass (HS, FT)
  C1087 – Compatibility of Sealants in Glazing Systems
  C1172 – Laminated Architectural Glass
  C1184 – Structural Silicone Sealants
  C1199 – Thermal Transmittance of Fenestration Systems
  C1253 – Outgassing Potential of Sealant Backing
  C1363 – Thermal Performance of Building Materials and Envelope Assemblies by means of a Hot Box Apparatus
  C1376 – Pyrolytic & Vacuum Deposition Glass Coatings
  C1401 – Structural Sealant Glazing Guide
  C1464 – Bent Glass
  D2200 – Pictorial Surface Preparation Standard for Painting Steel Surface
  D2224 – Standard Test Method for Calculation of Color Differences from Instrumentally Measured Color Coordinates
  D2247 – Standard Practice for Testing Water Resistance Coating in 100% Relative Humidity
  D412 – Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
  D3363 – Standard Test Method for Film Hardness by Pencil Test
  E84 – Surface Burning Characteristics
  E119 – Fire Tests of Building Construction
  E136 – Behavior at 750 °C Furnace
  E283 – Air Leakage through Windows & Curtain Walls
  E330 – Structural Performance by Air Pressure
  E331 – Water Penetration by Static Air Pressure
  F 476 – Standard Test Methods for Security of Swinging Door Assemblies
  E 547 – Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference
  E773 – Accelerated Weathering of IG Units
  E1105 – Field Water Penetration Testing
  E 1399 – Cyclic Movement and Measuring the Minimum and Maximum Joint width of Architectural Joint Systems
  E 2074 – Fire Test of Door assemblies, including Positives Pressure Testing of Side Hinged and Pivoted Swinging
  Door Assemblies -

AMERICAN WELDING SOCIETY (AWS)

• AWS D1.1/D1.1M – Structural Welding Code – Steel
  AWS D1.2/D1.2M – Structural Welding Code – Aluminum -

• BS 476-4 – Fire Tests on Building Materials and Structures: Non-Combustibility Test for Materials
  BS 476-6 – Fire Tests on Building Materials and Structures: Method for Fire Propagation of Products
  BS 476-7 – Fire Tests on Building Materials and Structures: Classification of Surface Spread of Flame
  BS 476-20 – Fire Resistance of Building Materials: General Principles
  BS 476-22 – Fire Resistance of Building Materials: Non-Load Bearing Elements
  BS 95201 – Glass for Glazing: Classification, Section 4
  BS 1161 – Aluminium Alloy Sections for Structural Purposes
  BS 1449-1.1 – Carbon and Carbon-Manganese Steel Plate, Sheet and Strip: General Specification
  BS 3692 – ISO Metric Precision Hexagon Bolts, Screws, and Nuts: Specification
  BS 3712-4 – Building and Construction Sealants: Test Method for Adhesion in Peel
  BS 3987 – Anodic Oxidation Coatings on Wrought Aluminium for External Architectural Applications
  BS 4255-1 – Rubber in Preformed Gaskets for Weather Exclusion: Non-Cellular Gaskets
  BS 4320 – Metal Washers for General Engineering Purposes (Metric Series)
  BS 4479-8 – Design of Articles to Be Coated: Recommendations for Vitreous Enamel Coatings
  BS 4652 – Zinc-Rich Priming Paint (Organic Media): Specification
  BS 4842 – Liquid Organic Coatings for Aluminium Alloy Extrusions, Sheet and Preformed Sections: External Architectural Applications
  BS 4871-3 – Approval Testing of Welders: Arc Welding of Tube-to-Tube Plate Joints
  BS 5588-0 – Fire Precautions in Buildings: Guide to Fire Safety Codes of Practice
  BS 5588-11 – Fire Precautions in Buildings: Code of Practice for Shops, Offices, Industrial, Storage and Similar Buildings
  BS 5750-8 (Amendment 1) – Quality Systems: Guide to Quality Management and Service Elements
  BS 5950-1 – Structural Use of Steelwork in Building: Code of Practice for Design in Simple and Continuous Construction
  BS 6161-18 – Anodic Oxidation Coatings on Aluminium: Test Method for Surface Abrasion Resistance
  BS 6180 – Barriers in and About Buildings: Code of Practice
  BS 6206 – Impact Performance of Flat Safety Glass and Plastics for Buildings
  BS 6213 – Selection of Construction Sealants
  BS 6262 – Building Code of Practice: Glass and Glazing
  BS 6375-1 – Performance of Windows: Classification of Weather Tightness
  BS 6399-1 – Loading for Buildings: Code of Practice for Dead and Imposed Loads
  BS 6399-2 – Loading for Buildings: Code of Practice for Wind Loads
  BS 6496 – Powder Organic Coatings for Aluminium Alloy Extrusions, Sheet and Preformed Sections: External Applications
  BS 6993-2 – Glazing Thermal and Radiometric Properties: Direct Measurement of U-Value
  BS 7475 – Fusion Welding of Austenitic Stainless Steel
  BS 7543 – Guide to Durability of Buildings, Elements, Products and Components
  BS 7664 – Undercoat and Finishing Paints: Specification
  BS 7668 – Weldable Structural Steels: Hot-Finished Hollow Sections in Weather Resistant Steels
  BS 7671 – Requirements for Electrical Installations (IEE Wiring Regulations)
  BS 7773 – Code of Practice for Cleaning and Preparation of Surfaces
  BS 8118-1 – Structural Use of Aluminium: Code of Practice for Design
  BS 8200 – Design of Non-Load Bearing External Vertical Enclosures of Buildings
  BS 8221-1 – Cleaning and Surface Repair of Buildings: Natural Stone, Brick, Terracotta and Concrete
  BS 8298 – Code of Practice for Design and Installation of Natural Stone Cladding and Lining -

• EN 13050 – Curtain Walling. Water tightness. Laboratory Test under Dynamic Condition of Air Pressure and Water Spray
  EN 287-1 – Qualification test of welders. Fusion welding. Steels.
  EN 485-1 – Aluminium and aluminium alloys. Sheet, strip and plate. Technical conditions for inspection and delivery
  EN 515 – Aluminium and aluminium alloys. Wrought products. Temper designations
  EN 572-2 – Glass in building. Basic soda lime silicate glass products. Float glass
  EN 755-2 – Aluminium and Aluminium Alloys – Extruded Rod/Bar, Tube and Profiles Part 2: Mechanical Properties
  EN 1026 – Windows and doors. Air permeability. Test method
  EN 1027 – Windows and doors. Water tightness. Test method
  EN 1363 – Fire resistance tests
  EN 1364 – Fire resistance test for non-load bearing elements
  EN 1863-2 – Glass in building. Heat strengthened soda lime silicate glass. Evaluation of conformity. Product standard
  EN 1993-1-3 – Eurocode 3. Design of steel structures. General rules. Supplementary rules for cold-formed members
  and sheeting
  EN 10025-1 – Hot rolled products of structural steels. Part 1: General technical delivery conditions
  EN 10025-6 – Hot rolled products of structural steels. Technical delivery conditions for flat products of high yield strength
  structural steels in the quenched and tempered condition
  EN 10051 – Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels – Tolerances on dimensions
  and shape
  EN 10088-2 – Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general
  purposes
  EN 10143 – Continuously hot-dip coated steel sheet and strip. Tolerances on dimensions and shape
  EN 10296-1 – Welded circular steel tubes for mechanical and general engineering purposes. Technical delivery conditions.
  Part 1: Non-alloy and alloy steel tubes
  EN 10297-1 – Seamless circular steel tubes for mechanical and general engineering purposes. Technical delivery conditions.
  Part 1: Non-alloy and alloy steel tubes
  EN 10326 – Continuously hot-dip coated strip and sheet of structural steels. Technical delivery condition
  EN 12002 – Adhesives for tiles. Determination of transverse deformation for cementitious adhesives and grouts
  EN 12004 – Adhesives for tiles. Definitions and specifications
  EN 12152 – Curtain walling. Air permeability. Performance requirements and classification
  EN 12153 – Curtain walling. Air permeability. Test method
  EN 12154 – Curtain walling. Water tightness. Performance requirements and classification
  EN 12155 – Curtain walling. Water tightness. Laboratory test under static pressure
  EN 12210 – Windows and doors. Resistance to wind load. Classification
  EN 12211 – Windows and doors. Resistance to wind load. Test method
  EN 12372 – Natural stone test methods – Determination of flexural strength under concentrated load
  EN 12373-1 – Aluminium and aluminium alloys. Anodizing. Method for specifying decorative and protective anodic oxidation
  coatings on aluminium
  EN 12600 – Glass in building. Pendulum test. Impact test method and classification for flat glass
  EN 13116 – Curtain walling. Resistance to wind load. Performance requirements
  EN 13161 – Natural stone test methods. Determination of flexural strength under constant moment
  EN 13438 – Paints and varnishes. Powder organic coatings for galvanized or sherardised steel products for construction
  purposes
  EN 13947 – Thermal performance of curtain walling. Calculation of thermal transmittance
  EN 14179 – Glass in building. Heat-soaked thermally-toughened soda lime silicate safety glass. Definition and description
  EN 62305-1 – Protection against lightning. General principles
  EN ISO 354 – Acoustics. Measurement of sound absorption in a reverberation room
  EN ISO 140-1 – Acoustics. Measurement of sound insulation in building and of building elements. Requirements for
  laboratory test facilities with suppressed flanking transmission
  EN ISO 1461 – Hot dip galvanized coatings on fabricated iron and steel articles. Specification and test methods
  EN ISO 2560 – Welding consumables. Covered electrodes for manual metal arc welding of non-alloy and fine grain steels.
  Classification
  EN ISO 3497 – Metallic coatings. Measurement of coating thickness. X-ray spectrometric methods
  EN ISO 8501-1 – Preparation of steel substrates, before application of paint
  EN ISO 12543 – Glass in building. Laminated glass and laminated glass safety glass. Laminated glass
  EN ISO 12944-4 – Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Types of surface
  and surface preparation
  EN ISO 14713 – Protection against corrosion of iron and steel in structures
  EN ISO 15613 – Specification and qualification of welding procedures for metallic materials. Qualification based on
  pre-production welding test
  EN ISO 3506-1 – Mechanical properties of corrosion-resistant stainless steel fasteners. Part 1: Bolts, screws and studs
  EN ISO 10077-2 – Thermal performance of windows, doors and shutters – Calculation of thermal transmittance – Part 2:
  Numerical method for frames
  EN ISO 10848-3 – Acoustics. Laboratory measurements of the flanking transmission of airborne and impact sound between
  adjoining rooms – Part 3: Application to light elements when the junction has a substantial influence
  EN ISO 11600 – Building construction. Jointing products. Classification and requirements for sealants
  EN 14179 – Glass in building – Heat soaked thermally toughened soda
  lime silicate safety glass -

• SS 212 – Specification for Aluminium Alloy Windows
  SS 381 – Specification for Curtain Walling Materials, Components and Test Methods
  SS CP 96 – Code of Practice for Curtain Walling -

• Qualicoat – Powder Coatings for Aluminum
  GANA Glazing Manual
  IGCC Certification
  NAAMM AMP 500 – Metal Finishes Manual
  OSHA STD1-2.3 / STD1-3.3 – Building Anchors for Suspended Platforms
  PCI MNL-120 / PCI Design Handbook (6th Edition) – Prestressed Concrete
  SSPC SP 1 – Solvent Cleaning
  SSPC SP 6 / NACE 3 – Commercial Blast Cleaning
  GSA FS DD-G-451d – Glass, Float or Plate
  GSA FS DD-G-1403c – Glass, Plate (Float), Spandrel
  CPSC 16 CFR 1201 – Safety Glazing Materials
  ASHRAE 90.1 – Energy Standard for Buildings
  AMCA 500-L, AMCA 501 – Louvers Testing & Application
  HEVAC (5th Edition) – Weather Louvers
  NFPA 80, 251, 252, 257, 259 – Fire Protection Codes
  UBC 7-1, 8-1, 26-1, 26-9 – Fire & Flammability Tests
  UL 9, 10B, 10C, 263 – Fire Test Standards
  IBC 2012 – International Building Code
  IEE Regulations (16th Edition) – Electrical Standards -